Search Results

The SAE G-27 committee was tasked by ICAO to develop a performance-based packaging standard for lithium batteries transported as cargo on aircraft. The standard details test criteria to qualify packages of lithium batteries & cells for transportation as cargo on-board passenger aircraft. Lithium batteries and cells have been prohibited from shipment as cargo on passenger aircraft since 2016. This paper summarizes the results of the tests conducted by Transport Canada and National Research Council Canada to support the development of this standard with evidence-based recommendations. It includes a description of the test specimens, the test set up, instrumentation used, and test procedures following the standard as drafted to date. The study considered several lithium-ion battery and cell chemistries that were tested under various proposed testing scenarios in the draft standard.

Fuel savings from truck platooning are generally attributed to an aerodynamic drag-reduction phenomena associated with close-proximity driving. The current paper is the third in a series of papers documenting track testing of a two-truck platoon with a Cooperative Adaptive Cruise Control (CACC) system where fuel savings and aerodynamics measurements were performed simultaneously. Constant-speed road-load measurements from instrumented driveshafts and on-board wind anemometry were combined with vehicle measurements to calculate the aerodynamic drag-area of the vehicles. The drag-area results are presented for each vehicle in the two-truck platoon, and the corresponding drag-area reductions are shown for a variety of conditions: gap separation distances (9 m to 87 m), lateral offsets (up to 1.3 m), dry-van and flatbed trailers, and in the presence of surrounding traffic.

The development of an optimized heat treatment schedule, with the aim of maximizing strength and relieving tensile residual stress, is important to prevent in-service cylinder distortion in Al alloy engine blocks containing cast-in gray iron liners. However, to effectively optimize the engine block heat treatment schedule, the current solutionizing parameters must be analyzed and compared to the as-cast condition to establish a baseline for residual stress relief. In this study, neutron diffraction was carried out to measure the residual stress along the aluminum cylinder bridge following solution heat treatment. The stresses were measured in the hoop, radial and axial orientations and compared to a previous measured as-cast (TSR) engine block. The results suggest that solution heat treatment using the current production parameters partially relieved tensile residual stress in the Al cylinder bridge, with stress relief being more effective near the bottom of the cylinder.

The continued need of vehicle weight reduction provides impetus for research into the development of novel automotive casting alloys and their processing technologies. Where possible, ferrous components are being replaced by aluminum (Al) and magnesium (Mg) alloy counterparts. This transition, however, requires a systematic optimization of the alloys and their manufacturing processes to enable production of defect-free castings. In this context, prevention of hot tears remains a challenge for Al and Mg alloy thin-wall castings. Hot tears form in semi-solid alloy subjected to localized tensile stress. Classical methods of stress measurement present numerous experimental limitations. In this research, neutron diffraction (ND) was used as a novel tool to obtain stress maps of castings and to quantify the effect of two processes used to eliminate hot tears in permanent mold castings: 1) increasing of the mold temperature during casting of Mg alloys, and 2) grain refinement of Al alloys.

Ice and snow accretion on aircraft surfaces imposes operational and safety challenges, severely impacting aerodynamic performance of critical aircraft structures and equipment. For optimized location-based ice sensing and integrated ‘smart’ de-icing systems of the future, microwave resonant-based planar sensors are presented for their high sensitivity and versatility in implementation and integration. Here, a conformal, planar complementary split ring resonator (CSRR) based microwave sensor is presented for robust detection of localized ice and snow accretion. The sensor has a modified thick aluminum-plate design and is coated with epoxy for greater durability. The fabricated sensor operates at a resonant frequency of 1.18 GHz and a resonant amplitude of -33 dB. Monitoring the resonant frequency response of the sensor, the freezing and thawing process of a 0.1 ml droplet of water is monitored, and a 60 MHz downshift is observed for the frozen droplet.

A study was conducted to assess the performance and castability of a new AA6061 aluminum alloy variant specially designed for semi-solid pressure die casting. The AA6061 alloy has very desirable mechanical properties for the fabrication of automotive parts. However, it has limited castability due to its low silicon content. It is not well suited for shape casting processes which are, for their part, very interesting in terms of production costs for complex-shaped automotive components. In an effort to meet automotive industry requirements, new AA6061 alloy variants have been developed by Rio Tinto Alcan researchers over the past years, aiming to improve the castability of the alloy while maintaining its desirable mechanical properties, by increasing its die-filling capacity, decreasing its hot tearing tendency. The study described herein is an example of how the performance of a single variant was assessed in terms of castability. The full study was conducted on six separate variants.

Development of lightweight alloys suitable for automobile applications has been of great importance to the automotive industry in recent years. The use of 319 type aluminum alloy in the production of gasoline engine blocks is an example of this shift towards light alloys for large automobile components. However, excessive residual stress along the cylinder bores of these engine blocks may cause problems during engine operation. Therefore, in this study, neutron diffraction was used to evaluate residual stresses along the aluminum cylinder bridge and the gray cast iron liners. The strains were measured in the hoop, radial, and axial orientations, while stresses were subsequently calculated using generalized Hooke's law. The results suggest that the residual stress magnitude for the aluminum cylinder bridge was tensile for all three measured components and gradually increased with cylinder depth towards the bottom of the cylinder.

Cast aluminum-silicon alloys have witnessed a notable increase in use in the automotive and transport industry. The ability of these alloys to be easily cast into complex shapes coupled with a favorable strength-to-weight ratio has given them an edge over cast irons. One particular area of casting which has received further and further attention is the area of semi-solid casting, where an alloy casting is prepared as slurry with flow properties that resemble both solid and liquid. In the present work, the effects of iron additions on the mechanical properties of a 319 semi-solid alloy were studied. This alloy was prepared using the SEED process, as developed by Rio Tinto Alcan in collaboration with the Aluminum Technology Centre of NRC Canada. The SEED (Swirled Enthalpy Equilibration Device) process is a novel rheocasting method which yields a semi-solid slurry from the mechanical stirring and cooling of the molten aluminum.

As a result of new regulations pertaining to the airworthiness of aircraft exposed to in-flight icing conditions where maximum water drop size is greater than 100 microns (referred to as Supercooled Large Droplet (SLD) conditions), updates are required to the test facilities and simulations that will enable manufactures to certify their products under these new rules. While a number of facilities report achieving some of the conditions specified in the new regulations, questions remain as to the suitability of the instrumentation used to measure the Liquid Water Content (LWC) and drop size distributions of the SLD icing cloud. This study aims to provide baseline LWC data through ice accretion measurement techniques on a NACA 0012 airfoil and rotating cylinders of varying diameters.

The National Research Council Altitude Icing Wind Tunnel liquid water content calibrations have historically relied on a 2.4 mm diameter rotating cylinder for drop sizes up to 50 μm and a 6.2 mm diameter rotating cylinder for drop sizes from 50 μm to 200 μm. This study compares the facility calibration, derived from rotating cylinder measurements, to water content measurements from the Science Engineering Associates Multi-Element Probe and the National Research Council Compact Iso-Kinetic Probe over a range of airspeeds and drop sizes. The data show where the rotating cylinder measurements may start to underestimate the liquid water content (LWC), possibly due to splashing at higher airspeeds and drop sizes. The data also show that the LWC read by the Multi-Element Probe is higher than that provided by the rotating cylinders, and the Compact Iso-Kinetic Probe (CIKP) reads higher than both other methods.

The influence of fuel aromatics type on the particulate matter (PM) and NOx exhaust emissions of a heavy-duty, single-cylinder, DI diesel engine was investigated. Eight fuels were blended from conventional and oil sands crude oil sources to form five fuel pairs with similar densities but with different poly-aromatic (1.6 to 14.6%) or total aromatic (14.3 to 39.0%) levels. The engine was tuned to meet the U.S. EPA 1994 emission standards. An eight-mode, steady-state simulation of the U.S. EPA heavy-duty transient test procedure was followed. The experimental results show that there were no statistically significant differences in the PM and NOx emissions of the five fuel pairs after removing the fuel sulphur content effect on PM emissions. However, there was a definite trend towards higher NOx emissions as the fuel density, poly-aromatic and total aromatic levels of the test fuels increased.

The ignition and combustion of natural gas directly injected into a multi-cylinder two-stroke diesel engine and ignited by a pilot liquid diesel injection has been investigated experimentally and with the aid of numerical simulation. Measurements of cylinder pressure and thermal efficiency were supplemented by endoscopic observation of flame development and three-dimensional numerical simulation of the ignition and combustion process. With gas/diesel fueling and appropriate injection timing, ignition delay and combustion duration can be about the same as with 100% diesel liquid fueling. Flame photography indicates that, for the same liquid diesel flow rate, subsequent injection of natural gas has a negligible effect on the ignition delay of the liquid fuel. Relative ignition timing is of major importance in obtaining successful combustion.

Lightweight tubular products offering enhanced stiffness and strength have always been of major concern for transportation and recreational applications. Hence, industries have turned to complex-shaped tubes to increase product performance and reduce energy costs. High-performance aluminum alloys, like 7075 for instance, have good mechanical properties such as high strength, but low formability at ambient temperature. Fortunately, hot tensile tests on 7075 samples have yielded an increase in formability with temperature. Therefore, testing has recently been launched at the Aluminum Technology Center to develop a new product application. More precisely, a 1,000-ton hydraulic press was equipped with +600°C heating plates and fitted with a bicycle handlebar mold. The plates provide 10 separate heating zones that can be adjusted independently. A thermo-mechanical model was also developed using LS-DYNA to determine tube temperatures around the heating zones.

Structural adhesive joints are expected to retain integrity in their entire service-life that normally involves cyclic loading concurrent with environmental exposure. Under such a severe working condition, effective determination of fatigue life at different temperatures is crucial for reliable joint design. The main goal of this work was thus defined as evaluation of fatigue performance of adhesive joints at their extreme working temperatures in order to be compared with their fracture properties under static loading. A series of standard double-cantilever-beam (DCB) specimens have been bonded by three structural 3M epoxy adhesives selected from different applications. The specimens were tested under monotonic and cyclic opening loads (mode-I) in order to evaluate the quasi-static and fatigue performances of selected adhesives at room temperature, 80°C and -40°C.

When performing calculations pertaining to the analysis of motor vehicle accidents, investigators must often select appropriate values for a number of parameters. The uncertainty of the final answers is a function of the uncertainty of each parameter involved in the calculation. This paper presents the results of recent tests conducted to obtain sample distributions of some common parameters, including measurements made with tapes, measurements made with roller-wheels, skidmark measurements, yawmark measurements, estimation of crush damage from photographs, and drag factors, that can be used to evaluate the uncertainty in an accident reconstruction analysis. The paper also reviews the distributions of some pertinent data reported by other researchers.

The exhaust emissions from a single-cylinder version of a heavy-duty diesel engine with exhaust gas recirculation (EGR) were studied using 12 diesel fuels derived from oil sands and conventional sources. The test fuels were blended from 22 refinery streams to produce four fuels (two from each source) at three different total aromatic levels (10, 20, and 30% by mass). The cetane numbers were held constant at 43. Exhaust emissions were measured using the AVL eight-mode steady-state test procedure. PM emissions were accurately modeled by a single regression equation with two predictors, total aromatics and sulphur content. Sulphate emissions were found to be independent of the type of sulphur compound in the fuel. NOx emissions were accurately modeled by a single regression equation with total aromatics and density as predictor variables. PM and NOx emissions were significantly significantly affected by fuel properties, but crude oil source did not play a role.

In this study, the AVL 8-mode steady-state simulations of the EPA transient test were conducted on a two litre single cylinder Ricardo Proteus research engine using two fuel matrices, one consisting fuels having different cetane numbers and the other consisting fuels of different aromatic contents. Engine exhaust emissions of NOx, HC, CO, CO2 and particulates were measured at two different injection timings. The results show that the single cylinder engine behaves similarly as a number of multi-cylinder production engines. The 8-mode simulation was also shown to produce exhaust emissions close to those obtained from the EPA transient test procedure. The cetane number response of the research engine indicates that an increase in cetane number of the fuel with cetane improvers reduced NOx emissions but increased particulate emissions.

The effects of impinging airflow on the near nozzle characteristics of an inwardly opening, high pressure-swirl atomiser are investigated in an optically-accessed, steady-state flow rig designed to emulate the intake flow of a typical, side-injected, 4-valve gasoline direct-injection combustion system. The results indicate that the impinging airflow has a relatively minor effect on the initial break-up of the fuel spray. However, the secondary break-up of the spray, i.e. the break-up of liquid ligaments, the spatial distribution of droplets within the spray and the location of the spray within the cylinder are significantly affected by the impinging air.

The demand for light weight vehicles continues to stimulate extensive research into the development of light weight casting alloys and optimization of their manufacturing processes. Of primary relevance are Aluminum (Al) and Magnesium (Mg) based alloys, which have successfully replaced selected iron based castings in automobiles. However, optimization of as-cast microstructure, processing and performance remains a challenge for some Al-based alloys. In this context, placement of chills in castings has been frequently used to locally manipulate the solidification conditions and microstructure of a casting. In this work, the effect of using an active copper chill on the residual strain profile of a sand-cast B319 aluminum alloy was investigated. Wedge-shaped castings were produced with three different cooling conditions: copper plate chill, copper pipe with cooling water and no chill (baseline).

A new injector has been designed for sequential injection of high-pressure natural gas and a quantity of liquid diesel fuel directly into diesel engine cylinders late in the compression stroke. Injected a few degrees before the natural gas, the pilot liquid fuel auto-ignites and serves, as it burns, to ignite the gaseous fuel which enters the chamber as an underexpanded sonic jet generating high local turbulence. Tests on a single-cylinder two-stroke engine with full electronic control have demonstrated the capability of this fueling method to nearly match conventional diesel engine efficiency over a wide range of load and substantially reduce the emissions of oxides of nitrogen (NOx), particulate mater (PM) and carbon dioxide (CO2).