Search Results

Relative rollover conditions of a heavy vehicle are analyzed to establish an array of potential dynamic rollover indicators towards development of an early warning device. A relative roll instability indicator defined as Roll Safety Factor (RSF) is proposed and shown to be a highly reliable indicator regardless of vehicle configurations and operating conditions. The correlation of various potential rollover indicators with the roll safety factor are then investigated for a 5-axle tractor semi-trailer combination using a comprehensive directional dynamic analysis model to determine the reliability of the proposed indicators over a range of operating conditions. The indicators are further examined in terms of measurability, lead time, and potential for application in an early warning system. The study shows that the trailer lateral acceleration and axle roll angles are closely correlated with the RSF.

Dynamic behavior of a partly-filled liquid cargo vehicle subject to simultaneous application of cornering and braking maneuvers is investigated through computer simulation. A three-dimensional quasi-dynamic model of a partly-filled tank of circular cross-section is developed and integrated into a comprehensive three-dimensional model of an articulated vehicle to study its directional response under varying steering and braking inputs, fill volumes and road surface friction. The liquid load movement encountered under combined steering and braking is expressed in terms of variations in the instantaneous c.g. coordinates and mass moments of inertia of the liquid bulk, assuming negligible influence of fundamental slosh frequency and viscous effects.

This paper summarizes the methodology and findings of an investigation to determine friction coefficients between typical loads and trailer deck materials in static, sinusoidal, and field measured random vibration environments. To conduct the tests in a controlled laboratory environment, a special sled-deck fixture was designed. Provisions were made to allow a change in sled-deck contact materials and to vary the load on the sled. For dynamic testing, the deck was subjected to sinusoidal and field based random signals obtained from tractor-trailer traversing paved and gravel roads. The results reveal that under vertical vibration, these friction coefficients can be as low as 25% of their corresponding static values. The random vibration tests revealed that friction coefficients can fall below 75% of the mean value for up to 35% of the total test duration. Thus, loads that rely on static friction for security may be highly prone to load shifts in a dynamic environment.

General purpose tank vehicles often carry partial loads in view of variations in the weight density of the liquid cargo and are thus subject to slosh loads during highway manoeuvres. The magnitude of destabilizing forces and moments due to liquid slosh is strongly related to a number of vehicle and tank design factors, such as tires, suspension, articulation mechanism, weights and dimensions, tank geometry and fill level. The rollover threshold of the tank vehicle is compared to that of an equivalent rigid cargo vehicle to demonstrate the destabilizing effects of liquid slosh. The rollover threshold of the tank vehicle is evaluated for a number of tank design factors. Influence of tank size and cross-section on the rollover threshold of the tank vehicles is investigated. The study concludes that the lateral load shift and thus the rollover threshold is strongly related to the tank cross-section geometry.

Dynamic interactions of urban buses with urban roads are investigated in view of the vibration environment for the driver and dynamic tire forces transmitted to the roads. The static and dynamic properties of suspension component and tires are characterized in the laboratory over a wide range of operating conditions. The measured data is used to derive nonlinear models of the suspension component, and a tire model as a function of the normal load and inflation pressure. The component models are integrated to study the vertical and roll dynamics of front and rear axles of the conventional and modern low floor designs of urban buses. The resulting nonlinear vehicle models are thoroughly validated using the fieldmeasured data on the ride vibration and tire force response of the buses.

An Active Independent Front Steering (AIFS) offers attractive potential for realizing improved directional control performance compared to the conventional Active Front Steering (AFS) system, particularly under more severe steering maneuvers. The AIFS control strategy adjusts the wheel steer angles in an independent manner so as to utilize the maximum available adhesion at each wheel/road contact and thereby compensate for cornering loss caused by the lateral load transfer. In this study, the performance potentials of AIFS are explored for vehicles experiencing greater lateral load transfers during steering maneuvers such as partly-filled tank trucks. A nonlinear yaw plane model of a two-axle truck with limited roll degree-of-freedom is developed to study the performance potentials of AIFS under different cargo fill conditions.

Technological developments in road vehicles over the last two decades have received considerable attention towards pushing the safe performance limits to their ultimate levels. Towards this goal, Active Front Steering (AFS) and Direct Yaw-moment Control (DYC) systems have been widely investigated. AFS systems introduce corrective steering angles to conventional system in order to realize target handling response for a given speed and steering input. It is thus expected that such an action under severe maneuvers may cause one tire to reach saturation while the other tire may be capable of developing more force. This study, therefore, proposes an Active Independent Front Steering (AIFS) system capable of controlling a wheel independently. At low speeds, the proposed AIFS system will modify the steer angle with speeds while maintaining pro-ackerman geometry similar to an AFS system. In doing so, it will realize a target response defined as one provided by a neutral steer system.

In this study, the enhancement of road friendliness of Heavy Goods Vehicle is investigated using two methods to control the resonant forces: (i) Determination of optimal asymmetric force velocity characteristics of the suspension dampers to control the wheel forces corresponding to the resonant modes; (ii) Optimal design of an axle vibration absorber to control the wheel forces corresponding to the unsprung mass resonance mode. An analogy between the dynamic wheel loads and ride quality performance characteristics of heavy vehicles is established through analysis of an in-plane vehicle model. A weighted optimization function comprising the dynamic load coefficient (DLC) and the overall rms vertical acceleration at the driver's location is formulated to determine the design parameters of the damper and absorber for a range of vehicle speeds. The results show that implementation of tuned axle absorbers can lead to reduction in the DLC ranging from 11.5 to 21%.

Ride quality of articulated vehicles is investigated via computer simulation in view of secondary suspension parameters. A tractor-semitrailer vehicle is modelled incorporating primary as well as secondary suspension. The ride vibration levels at the cab floor and at the driver-seat interface are evaluated using power spectral density approach. The effect of various vehicle parameters, such as secondary suspensions, primary suspensions, axle loads and tires on the vehicle ride quality is presented, and the significance of secondary vehicle suspension is specifically emphasized. A software package is developed to evaluate and assess the ride performance of articulated vehicles with suspended seat and cab. A limited validation of the computer ride model is achieved via field measurements.

Low frequency terrain induced vibrations transmitted to the off-road vehicle operators are quite severe and exceed I.S.O specified “fatigue decreased proficiency” limits. In this paper, the ride improvement of an agricultural tractor is sought through effective designs of passive seat suspensions. The dynamic analysis of existing bounce suspension seats is carried out to establish its ride performance behaviour. Optimal bounce seat suspension parameters are selected with an objective to maintain the ride vibration levels within 4 hours exposure “fatigue decreased proficiency” limits. The roll and pitch ride vibrations, perceived by the operators, can be attenuated through a gimbal arrangement mounted to the bounce suspension seat. The optimal parameters of the combined seat isolator are selected using parametric optimization techniques. Also a horizontal isolator, attachable to the bounce or the combined seat isolator, is configured.