Search Results

The work presented here seeks to compare different means of providing scavenging systems for an automotive 2-stroke engine. It follows on from previous work solely investigating uniflow scavenging systems, and aims to provide context for the results discovered there as well as to assess the benefits of a new scavenging system: the reverse-uniflow sleeve-valve. For the study the general performance of the engine was taken to be suitable to power a medium-duty truck, and all of the concepts discussed here were compared in terms of indicated fuel consumption for the same cylinder swept volume using a one-dimensional engine simulation package. In order to investigate the sleeve-valve designs layout drawings and analysis of the Rolls-Royce Crecy-type sleeve had to be undertaken.

Manufacturers of heavy-duty diesel engines are facing increasingly stringent, emission standards. These standards have motivated new research efforts towards improving the performance of diesel engines. The objective of the present program is to develop a comprehensive analytical model of the diesel combustion process that can be used to explore the influence of design changes. This will enable industry to predict the effect of these changes on engine performance and emissions. A major benefit of the successful implementation of such models is that engine development time and costs would be reduced through their use. The computer model is based on the three-dimensional KIVA-II code, with state-of-the-art submodels for spray atomization, drop breakup / coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, and soot and radiation.

The measurement of the contact forces between road and tires is of fundamental importance while designing road vehicles. In this paper, the design and the employment of measuring wheels for trucks and heavy vehicles is presented. The measuring wheels have been optimized in order to obtain high stiffness and the approximately the same mass of the wheels normally employed. The proposed multicomponent measuring wheels are high- accuracy instruments for measuring the dynamic loads during handling and durability testing. The measuring wheels can replace the wheels of the truck under normal operation. Such family of wheels plays a major role in modern road vehicles development. The measuring wheel concept design is based on a patented three-spoke structure connected to the wheel rim. The spokes are instrumented by means of strain gauges and the measuring wheel is able to measure the three forces and the three moments acting at the interface between the tire and the road.

A quasi-dimensional computer simulation model is presented to simulate the thermodynamic and chemical processes occurring within a spark ignition engine during compression, combustion and expansion based upon the laws of thermodynamics and the theory of equilibrium. A two-zone combustion model, with a spherically expanding flame front originating from the spark location, is applied. The flame speed is calculated by the application of a turbulent entrainment propagation model. A simplified theory for the prediction of in-cylinder charge motion is proposed which calculates the mean turbulence intensity and scale at any time during the closed cycle. It is then used to describe both heat transfer and turbulent flame propagation. The model has been designed specifically for the two-stroke cycle engine and facilitates seven of the most common combustion chamber geometries. The fundamental theory is nevertheless applicable to any four-stroke cycle engine.

The planar rigid bicycle model is one of the most popular models used in vehicle dynamics. It has widely been used in studying vehicle handling characteristics and designing steering control system for vehicles. This paper analyses a modified dynamic model called the "Elastic Bicycle Model." This model improves upon the classical bicycle model by taking into account the flexibility of the vehicle frame by using concepts from the Euler beam theory. Complete set of the resulting dynamic equations of this model are presented. Non-dimensional versions of the equations are used to investigate the steady state response of the model. Finally, the results of the response study obtained by modeling a small truck with an elastic model and the classical bicycle model are presented. These include the steady state solutions as function of different parameters as well as a transient solution in response to a saw-tooth steering input and a step input. Octave® has been used for simulation purpose.

This paper discusses controller development for an active, off-road vehicle suspension system. A brief review of electronic filters and their characteristics is used to provide insight on the difficulties of designing a control algorithm for negotiating hilly and rough terrain at higher speeds. Two controller designs are presented. One was designed by pole placement and causes the suspension response to approximate a Type 1 Chebychev filter. The other was designed using constrained optimization. A comparison and discussion of simulation results leads to the conclusion that the suspension should be adaptively or predictively controlled for arbitrary terrain and velocity conditions.

This paper describes a general purpose computer graphics interface for performing detailed two- and three-dimensional studies involving the dynamic response of humans and vehicles during the pre-crash, crash and post-crash phases of a motor vehicle accident. Specifications are provided for human, vehicle and environment models which can be constructed and analyzed using the interface. The requirements of analysis methods which may be incorporated into the interface are examined, and several examples are provided. Finally, the paper illustrates how the interface is used for creating high-level animations to view the resulting human and/or vehicle motion on various output devices such as computer displays, printers, plotters and video tape recorders.

The classical methods of deflection analysis are finding more application to complex automotive chassis frame structures. Much too time consuming for manual application, they are now coming into more widespread use with the aid of high-speed computers. This paper describes a computerized deflection analysis for complete truck frames under the cases of torsion and flexure. The rapid, accurate analysis permits investigation of more design problems resulting in the eventual production of more efficient frame structures.

Trucks can carry heavy load and when applying the brakes during for example a mountain downhill or for an abrupt stop, the brake temperatures can rise significantly. Elevated temperatures in the drum brake region can reduce the braking efficiency or can even cause the brake system to fail, catch fire or even break. It therefore needs to be designed such to be able to transfer the heat out of its system by convection, conduction and/or radiation. All three heat transfer modes play an important role since the drum brakes of trucks are not much exposed to external airflow, a significant difference from disk brakes of passenger cars analyzed in previous studies. This makes it a complex heat transfer problem which is not easy to understand. Numerical methods provide insight by visualization of the different heat transfer modes. Presented is a numerical method that simulates the transient heat transfer of a truck drum brake system cooldown at constant driving speed.

Wet multiple plate clutches consist of friction plates, on which a friction material is bonded, and mating plates that are plain metal plates. Since the frequency and the range of load in the field of forklift trucks vary widely and are more severe than those for passenger cars, the wet multiple plate clutches on forklift trucks are often damaged. Damaged clutches that were returned from the field typically had 3 types of symptoms: 1.Only the friction material was damaged, 2.Only the mating plates were deformed, 3.Both symptoms were observed. It was clear that the cause of these symptoms depended on the difference of the operating application and the strength criteria of each part. This showed that a design guide for wet multiple plate clutches considering the strength balance between the two parts according to the work application was required. The relevant flow chart of this design process was proposed.

In order to fulfill the technical requirements of a high-efficiency low-emissions off-road horizontal diesel engine, a unique design is proposed and optimized in this paper for the cooling water jacket structure with a forced-cooling closed-loop cooling system. The cooling water flow rate, temperature, and pressure at the inlet and several other critical locations of the cooling water jacket were measured and analyzed at different engine operating conditions for the water jacket designs. A numerical simulation model of the coolant flow and the cooling system was built and used to analyze the thermal/fluid characteristics of the coolant flow in the water jacket. The impact of different structural and packaging design parameters on coolant flow and heat transfer was investigated. The design deficiency of an original (earlier) design of the water jacket was pointed out and an improved design was proposed.

Paper describes analysis of the design process of modern automotive LPG and CNG containers. Over decade experience in the field of both computer based analysis as well as in the real conditions testing has been collected and presented in the paper. Authors present the potentials of modern FEM methodologies in the optimization and production of lightweight steel containers. It has been proved that the most sophisticated numerical analysis have to be followed by the construction verification, particularly considering direct exposure to fire. Bonfire test have become obligatory for both liquid and compressed gases containers. Properly chosen fire protection system, together with the adequate level of quality of materials applied for its production together with proper directing of the gas flowing out from safety devices are the essential factors defining gas containers fire safety.

A direct method is developed for designing a vehicle fuel filler door with torsional spring. The design parameters include the door's geometrical parameters and spring dimensions. The design requirements are based on the finger force curve during closing and opening, and the bending stress in the spring. An example is included to demonstrate the effectiveness of the new method.

Planning for charging in transport missions is vital when commercial long-haul vehicles are to be electrified. In this planning, accurate range prediction is essential so the trucks reach their destinations as planned. The rolling resistance significantly influences truck energy consumption, often considered a simple constant or a function of vehicle speed only. This is, however, a gross simplification, especially as the tire temperature has a significant impact. At 80 km/h, a cold tire can have three times higher rolling resistance than a warm tire. A temperature-dependent rolling resistance model is proposed. The model is based on thermal networks for the temperature at four places around the tire. The model is tuned and validated using rolling resistance, tire shoulder, and tire apex temperature measurements with a truck in a climate wind tunnel with ambient temperatures ranging from -30 to 25 °C at an 80 km/h constant speed.

In the near future, GM will introduce a new product to the marketplace. The vehicle is a full-size, four-door utility vehicle based on its current C/K full-size truck product line. This new vehicle is smaller than the current Suburban and does not provide room for a third seat. It is expected that this utility will supplement the small truck four-door utility and create a new market niche with its unique size and features. The process used to design, develop and validate the new product in an aggressive 93-week time frame, is the subject of this paper.

In this paper, a simplified and systematic approach to integrate reliability and durability aspects in design process is presented. A six step process is explained with the help of examples. Two alternatives for gathering means and standard deviations for key parameters are discussed. First a DOE approach based on orthogonal arrays is presented. Second approach is based on Taylor Series expansion. An example of beam design is solved with both of these approaches. The Second example also considers the degradation with time in service.

As a non-predictive model of the scavenging process, a generalized thermodynamic model has been suggested. This model can give a thermodynamic description for any possible scavenging process. Having specified a history of the scavenging process, this model is suitable for all scavenging systems including cross, loop and uniflow scavenging schemes. For the simplified isobaric and isochoric model with respectively constant coefficients of intake and discharge proportions during different scavengine phases, analytical solutions for this model have been obtained. From these, all existing models with the isobaric and isochoric assumptions can be derived.

A lightweight design method of vehicle dash insulators is proposed and investigated in this paper. The lightweight dash insulator, which is composed of double layers of cotton felt with different density and a layer of polyethylene (PE) film and has 55% decrease in weight, is developed and applied in a passenger car, instead of the traditional “heavy layer-soft layer” dash insulator. To evaluate the NVH performance of the lightweight dash insulator, the noise reduction (NR) level index is calculated by using SEA simulation and the sound pressure level and sound qualities in the vehicle are tested under the driving conditions for wide open throttle acceleration in third gear and 60km/h cruising in fourth gear. The simulation and test results show that the vehicle with the lightweight dash insulator has better NVH performance.

A lumped-parameter thermal network model, based on the analogy between heat transfer and electric current flow, is presented for hybrid powertrain cooling systems. In order to optimally select the powertrain components that are commercially viable and meet performance, emission, fuel economy and life targets, it is necessary to consider the influence of cooling architecture. Especially in electric and hybrid vehicles, temperature monitoring is important to increase power and torque utilization while preventing thermal damages. Detailed thermal models such as FEA and CFD are considered for component level assessments as they can locate thermal hotspots and identify possible design changes needed. However, for the system level analysis, the detailed numerical models are not suitable due to the requirement of high computation effort.

This paper describes the design strategy adopted for developing a new high performance actuation system referred to as the ElectroHydraulic Actuator (EHA). The design approach can be divided into fives phases that include: pre-conceptual analysis, conceptual design, preliminary design, detailed design and, integration and test. An important aspect of the design process is the use of modeling and simulation for the analysis, sizing and selection of off-the-shelf parts, and for the detailed design of new custom made components. EHA is based on hydrostatic transmission. It is a unique device with its own characteristics and requires hydraulic components that are specifically tailored to its needs. A prototype of EHA has been produced and has demonstrated an extremely high level of performance. The performance of this prototype complies with design requirements and validates the chosen design approach.