Search Results

This paper gives a thorough review of the HC/CO emissions challenge and discusses the effects of different diesel oxidation catalyst designs in a pre turbine and post turbine position on steady state and transient turbo charger performance as well as on HC and CO tailpipe emissions, fuel economy and performance of modern Diesel engines. Results from engine dynamometer testing are presented. Both classical diffusive and advanced premixed Diesel combustion modes are investigated to understand the various effects of possible future engine calibration strategies.

To meet LEV and EU Stage III emission requirements, it is necessary for new catalytic converters to be designed which exceed light-off temperature as quickly as possible. The technical solutions are secondary air injection, active heating systems such as the electrically heated catalytic converter, and the close coupled catalytic converter. Engine control functions are extensively used to heat the converter and will to play a significant role in the future. The concept of relocating the converter to a position close to the engine in an existing vehicle involves new conflicts. Examples include the space requirements, the thermal resistance of the catalytic coating and high temperature loads in the engine compartment.

Emission legislations for the light / medium and heavy duty vehicles are becoming more and more stringent worldwide. Tightening of NOx and Particulate Matter (PM) limits further from Euro III to Euro IV levels has provoked the need of either controlling NOx from the engine measures and use PM control after-treatment devices such as Partial Flow Filters, or, controlling PM from the engine measures and use NOx control devices such as Selective Catalytic Reduction (SCR) systems. Manufacturers have adopted different strategies, depending upon the suitability, cost factors, infrastructure development and ease of maintenance of these systems. PM Metalit®, is a partial flow filter, which captures particulates coming out of the exhaust and re-generates on a continuous basis with the help of Nitrogen Dioxide (NO2) in the exhaust.

This paper gives an overview of the development work for an aftertreatment system, used in hand held powertools to fulfil the corporate average US Limits. The paper will start with a description of the annual reductions in US Limits with differences in CARB and EPA legislation and the consequences of the legislation in Europe from 2007 onwards. There then follows a chapter describing space restrictions in the given muffler leading to a maximum size for the substrate. Tests results are shown, giving an idea of additional measures taken to avoid dangerous temperatures on the muffler surface and of the emitted exhaust gas. The exothermic temperature increase created under service conditions imposes an additional thermal load from the catalyst back towards the engine itself. Therefore, some modifications regarding gas flow and positioning of the catalyst had to be made to find an adequate solution for series production.

In order to match catalyst OBDII conditions the common procedure is oven aging with air, which is not suitable for complete converter systems due to mantle corrosion. The goal was, therefore, to find an alternative procedure to ensure a defined catalyst aging that would match 1,75 times the emission standard and is also good for SULEV. The new procedure currently being developed allows the aging of metal and ceramic catalysts as well as complete catalyst systems. The paper will present the aging process, emission data of fresh and aged catalysts and the feedback to the test car OBDII system.

The influence of physical parameters of the catalyst's substrate such as thermal mass, hydraulic diameter and geometric surface area on catalyst's efficiency is well known as published in numerous works. This paper will show interactions of these parameters and will provide a guideline on how to design the optimum system for a specific application, taking into account system's back pressure and system costs. Based on engine test bench results that show the influence of the physical parameters, the results for the optimized design regarding emission tests and maximum conversion rate at higher loads will be demonstrated.

A study was performed to develop optimum design strategies for a production V6 engine to maximize catalyst performance at minimum pressure loss and at minimum cost. Test results for an advanced system, designed to meet future emission limits on a production V6 vehicle, are presented based on FTP testing. The on-line pressure loss and temperature data serves to explain the functioning of the catalyst.

Nearly all real Diesel engine operation is leading to low exhaust temperatures. Standard catalyst technique remains therefore for significant time below light off. To improve the conversion behavior two approaches were made: placement of tailor fitted catalysts as close as possible to the engine exhaust port before turbocharger and usage of close coupled catalysts with the so-called hybrid design. Both measures are providing visible progress in reducing Diesel engine emissions. Tests were made with modern Diesel engines both for passenger cars and heavy duty vehicles.

Future catalyst systems need to be highly efficient in a limited packaging space. This normally leads to a design where the flow distribution, in front of the catalyst, is not perfectly uniform. Measurements on the flow test bench show that the implementation of perforated foils for the corrugated and flat foils has the capability to distribute the flow within the channels in the radial direction so that the maximum of the given catalyst surface is of use, even under very poor uniformity indices. Therefore a remarkable reduction in back pressure is measured. Emission results demonstrate cold start improvement due to reduced heat capacity. The use of LS - structured ( Longitudinal structured ) corrugated foils creates a high turbulence level within the single channels. The substrate lights-up earlier and the maximum conversion efficiency is reached more quickly.

Nearly all real diesel engines operations are leading to low exhaust temperatures. Standard catalyst technique remains therefore for significant time below light-off. To improve the conversion behavior two approaches were made: placement of tailor-fitted catalysts as close as possible to the engine exhaust port before turbocharger and usage of close coupled catalysts with the so-called hybrid design. Both measures are providing visible progress in reducing diesel engine emissions. Tests were made with modern diesel engines both for passenger cars and heavy-duty vehicles.

It has been shown within the catalyst industry that the emission performance with higher cell density technology and therefore with higher specific geometric area is improved. The focus of this study was to compare the overall performance of high cell density catalysts, up to 1600cpsi, using a MY 2001 production vehicle with a 4.7ltr.V8 engine. The substrates were configured to be on the edge of the design capability. The goal was to develop cost optimized systems with similar emission and back pressure performance, which meet physical and production requirements. This paper will present the results of a preliminary computer simulation study and the final emission testing of a production vehicle. For the pre-evaluation a numerical simulation model was used to compare the light-off performance of different substrate designs in the cold start portion of the FTP test cycle.

The effects of the internal geometry of catalytic converter channels on flow characteristics; exhaust backpressure and overall conversion efficiency have been investigated by means of both numerical simulations and experimental investigations. The numerical work has been carried out by means of a micro scale numerical tool specifically tailored for flow characteristics within converter channels. The results are discussed with aid of flow distribution patterns within the single cell and backpressure figures along the catalyst channel. The results of the numerical investigation provide information about the most efficient channel shapes. An experimental validation of the simulated results has been carried out with a production 3.6 liter, 6-cylinder engine on a dynamic test bench. Both modal and bag emission data have been measured during the FTP-Cycle.

The influence of catalyst volume, cell density and precious metal loading on the catalyst efficiency were investigated to design a low cost catalyst system. In a first experiment the specific loading was kept constant for a 500cpsi and a 900cpsi substrate. In a second experiment the palladium loading was reduced on the 900cpsi substrate and the same PM loading was applied to a 1200cpsi substrate with lower volume. Finally the loading was further reduced for the 1200cpsi substrate. The following parameters were studied after aging: Catalyst performance of standard cell density compared to high cell density technology Light-off performance and catalyst efficiency as a function of Palladium loading and substrate cell density Catalyst efficiency as a function of AFR biasing The performance of the aged catalysts was investigated in a lambda sweep test and in light-off tests at an engine bench.

In order to achieve ultra low emission levels with three-way catalysts, an early accurate air/fuel ratio control is essential. Positioning the oxygen sensor in the first part of the substrate helps to protect the oxygen sensor from being splashed by water during cold start, so that early heating and activation becomes a less limiting factor. For emission control purpose, a position of a rear sensor in the warm part of the catalyst gives improved possibilities for oxygen buffer control during catalyst warming up conditions. This enhances balancing HC and NOx in an early phase. In addition, for OBD reasons it is possible to locate the sensor in any axial position in the catalyst, which improves design possibilities for cold start detection, even for single brick catalyst systems. The paper describes the construction of the catalyst with an integrated oxygen sensor.

On one hand, latest worldwide emissions legislation developments aim to reduce NOx and Particulate Matter (PM) emissions of all diesel engines, while on the other hand lower fuel consumption diesel engines are still required for lower fleet average CO₂ emissions. As a consequence of the chosen CO₂ optimized combustion mode, the raw NOx emission increases and as such Selective Catalytic Reduction (SCR) technology will be the future choice for high efficiency NOx aftertreatment. This paper deals with SCR technology and its derivative SCRi® technology, when diesel particle reduction is required, especially for heavy-duty applications. Alongside the developed metal catalyst technologies, a complete SCR reducing agent dosing system is presented. Emission results gained with the SCR or SCRi® technologies on European commercial engines illustrate the potential of these technologies for conversion of NOx and PM emissions.

More efficient and durable catalytic converters for the two- and three-wheeler industry in developing countries are required at an affordable cost to reduce vehicle emissions, to maintain them at a low level and therefore to participate in a cleaner and healthier environment. This particularly is true nowadays, because the demand and prices of Platinum Group Metal (PGM) for catalyst are continuously increasing due to i) the worldwide progressive implementation of motorcycles emission legislations similar to Euro 3 Stage requiring catalysts, ii) the need for non-road diesel vehicles to be equipped now with catalyst systems, and iii) the constant increase of the worldwide automobile market. A new generation of metallic substrates with structured foils for catalytic converters is proven to be capable of improving conversion behavior, even with smaller catalyst size.

Further advancements in engine development lead to increased fuel efficiency and reduced CO₂ emission. Such low emission engine concepts require most advanced exhaust gas aftertreatment systems for lowest possible tailpipe emissions. On the other hand, the exhaust gas purification by catalytic measures experiences more and more challenges due to constantly reduced exhaust gas temperatures by more efficient engines. These challenges can be overcome by traditional catalyst heating strategies, which are known to increase fuel consumption and emissions. Alternatively, electrically heated catalysts ("EHC") can be utilized to provide a very efficient method to increase gas temperatures directly in the exhaust catalyst. This way the energy input can be tailored according to the component need and the energy loss in the system can be minimized.

In studying H2S emissions, it is desirable to have an analytical technique which is rapid, continuous, accurate and easy to use in a laboratory or vehicle exhaust environment. Typically, H2S has been measured using the EPA impinger method with collection times on the order of 1 to 2 minutes. Other techniques have been developed with significantly shorter response times. However, it has been shown that the major release of H2S occurs in less than 20 seconds after a vehicle changes from rich to lean operation. Therefore, it is highly desirable to have an H2S analytical technique with a response time of less than 10 seconds. In this paper, the benefits of use of a chemical ionization mass spectrometer (CIMS) to continuously monitor H2S and SO2, emissions are reported. Using the CIMS technique, the effects of several operating parameters on the release of H2S and SO2 from automotive catalysts were studied.

Modern Diesel Engines equipped with Common-Rail Direct Injection and EGR are characterized by an increasingly high combustion efficiency. Consequently the exhaust gas temperature, especially during a cold start, is significantly reduced compared to typical values measured in previous engine generations. This leads to a potential problem with CO emission limit compliance. The present paper deals with an experimental investigation of turbulent-flow metal substrates, carried out on a vehicle roller bench using a production 1.3 Liter diesel engine equipped passenger car. The tested metal supported catalysts proved to yield extremely high conversion rates both during cold start and in warm operation phase. The improved mass transfer efficiency of the advanced metal substrates is related on one hand to the optimized coating technology and, on the other hand, to the enhanced flow performance in the single converter channels which is caused by structured metal foils.

From SAE-Papers and several publications, the easy, effective function and management of an EHC-System is well known. The direction of the development is now to reduce the electrical energy consumption and to show the mechanical durability of the heating structure. This paper shows that it is possible to minimize the energy consumption and that the required service life can be in principle achieved with the introduction of these developments. The physical characteristics such as mass, geometrical surface area, cell density and electrical resistance of the EHC construction could be optimized to save energy. This, in conjunction with the operating parameters of the engine, the controlling of the secondary air and the catalyst configuration, will enable the goals to be met. The design of the converter, the physical characteristics and the results of the tests are shown with the Porsche 944 S2 and 968 applications.