Search Results

An experimental and numerical study was conducted on the spray and mixture properties of a hole-type injector for direct injection (D. I.) gasoline engines. The Laser Absorption Scattering (LAS) technique was adopted to simultaneously measure the spatial concentration distributions and the mass of the liquid and vapor phases in the fuel spray injected into a high-pressure and high-temperature constant volume vessel. The experimental results were compared to the numerical calculation results using three-dimensional CFD and the multi-objective optimization. In the numerical simulation, the design variable of the spray model was optimized by choosing spray tip penetration, and mass of liquid and vapor phases as objective functions.

Experimental and computational studies were carried out to characterize the spray development and evaporation processes of multi-hole injector for direct injection spark ignition (DISI) engines. The main injector parameter to be investigated in this study is a diverging angle between neighboring two holes. In the experimental study, the influence of the diverging angle on evaporation process of fuel spray from two-hole injector was investigated using Laser Absorption Scattering (LAS) measurement. Smaller diverging angle causes larger spray tip penetration because the momentum of the spray from one hole emphasizes another, when two spray merge to one. Moreover, spray tip penetration decreases at certain diverging angle due to the negative pressure region between two sprays. Mechanisms behind the above spray behaviors were discussed using the detailed information on the spray and ambient gas flow fields obtained by the three dimensional computational fluid dynamics (CFD).

Measurements of the droplet and ambient air velocities in and around a D.I. gasoline spray were made by combining the laser induced fluorescence (LIF) and the particle image velocimetry (PIV) techniques. Before the fuel spray was injected into a constant volume vessel, rhodamine B-water solution was injected into the ambient air by a swirl-type injector for dispersing the fine fluorescent liquid particles as tracers for the ambient air motion. The fuel spray was injected into the fluorescent tracer clouds by a D.I. gasoline injector and was illuminated by an Nd:YAG laser light sheet (wave length: 532 nm). The light scattered by the droplets in the fuel spray was the same as the Nd:YAG laser wavelength, whereas the light emitted by the fluorescent tracer clouds was at a longer wavelength.

Mixture formation processes play a vital role on the performance of a D.I. Gasoline engine. Quantitative measurement of liquid and vapor phase concentration distribution in a D.I. gasoline spray is very important in understanding the mixture formation processes. In this paper, an unique laser absorption scattering (LAS) technique was employed to investigate the mixture formation processes of a fuel spray injected by a D.I. gasoline injector into a high pressure and temperature constant volume vessel. P-xylene, which is quite suitable for the application of the LAS technique, was selected as the test fuel. The temporal variations of the concentration distribution of both the liquid and vapor phases in the spray were quantitatively clarified. Then the effects of injection pressure and quantity on the concentration distributions of both the liquid and vapor phases in the spray were analyzed.

The purpose of this study was to investigate the effect of residual gas fraction and compositions on the ignition delay of a diesel spray. The air residual gas mixture was produced by injecting diesel sprays into a constant volume combustion bomb with no scavenging burned gas in it. The air initially contained in the bomb was enough to completely burn the fuel supplied by more than 20 injections. The spray injected in the bomb was ignited by the self-ignition process affected by the residual gas. Repetitions of the fuel injection raised the fraction of residual gas in the bomb. The ignition delay in each injection was measured by a photo-transistor. The ignition delay was a minimum when the ambient mixture contained about 4 % residual gas. The effect of residual gas compositions was investigated by adding small amount of CO, CO2 and THC into the bomb. The CO and CO2 compositions in the burned gas produced an elongation of the ignition delay, while the THC shortened the delay period.

Quantitative imaging of the fuel concentration distribution was made in the combustion chamber of a propane-fueled spark ignition (SI) engine with the employment of laser-sheet-induced Rayleigh scattering technique for realizing the remote, nonintrusive and highly space- and time-resolved measurement. The original engine was modified to introduce YAG laser-induced sheet light into the combustion chamber and the scattered light was captured by a CCD camera fitted with a gated double-micro- channel plate image intensifier. The measurements were done at the crank angle of 270°ATDC in the combustion chamber of the engine motored at 200rpm with an air fuel ratio of 13 for various injection timing, injection direction and intake flow. The results show that with an appropriate matching of fuel injection timing, injection direction and intake flow, a stratified distribution of the fuel concentration can be realized.

Cross-sectional distributions of the liquid phase temperatures in fuel sprays were measured using a laser-induced fluorescence technique. The liquid fuel (n-hexadecane or squalane) was doped with pyrene(C16H10). The fluorescence intensity ratios of the pyrene monomer and excimer emissions has temperature dependence, and were used to determine the liquid phase temperatures in the fuel sprays. The measurements were performed on two kinds of sprays. One was performed on pre-heated fuel sprays injected into surrounding gas at atmospheric conditions. The other was performed on fuel sprays exposed to hot gas flow. The spray was excited by laser radiation at 266nm, and the resulting fluorescence was imaged by an intensified CCD camera. The cross-sectional distribution of the liquid phase temperature was estimated from the fluorescence image by the temperature dependence of the intensity ratio.

The two-dimensional distributions of the liquid phase temperatures in diesel sprays injected into high-pressure and high-temperature environments were measured using the laser-induced fluorescence technique. The liquid fuel (n-hexadecane) was doped with pyrene(C16H10). The fuel spray doped with pyrene was injected under a high-pressure of 3.1MPa and a high-Temperature of 773K. The evaporating diesel spray was excited by laser radiation at 266nm, and the resulting fluorescence was imaged by an intensified CCD camera. The fluorescence intensity ratios of the pyrene monomer and excimer emissions have temperature dependence, and were used to determine the liquid phase temperatures in the diesel sprays. The cross-sectional distribution of the liquid phase temperature was estimated from the fluorescence images by the temperature dependence of the intensity ratio.

In the previous study of the authors, it was found that some benefits for the mixture preparation of DI gasoline engines can be offered by splitting the fuel injection, such as the phenomenon of high density liquid phase fuel piling up at the leading edge of the spray can be circumvented. In a further analysis, the vapor quantity in the “stable operating” range (equivalence ratio of vapor ϕv in a range of 0.7≤ϕv≤1.3) was significantly increased by the split injection compared to the single injection. In this work, the mechanism of the effect of the split injection on the mixture formation process was studied by combining the laser-sheet imaging, LIF-PIV and the LAS (Laser Absorption Scattering) technique. As a result, it is found that the spray-induced ambient air motion can help the formation of the more combustible mixture of the split injection whereas it played a minus role of diluting the spray by the single injection.

Simplified visualization of the fuel spray developing process in a small D.I. diesel engine was made by the liquid injection technique. In this technique, a liquid fuel was injected into another liquid to simulate injection into a high pressure gaseous atmosphere. For obtaining spray characteristics in the liquid similar to a diesel spray in a high-pressure gaseous atmosphere, the similarity principles based on the Reynolds number of the fuel flow at a nozzle hole and empirical equations of the spray penetration including the breakup length were introduced in this study. Especially, the injector was newly designed for the liquid injection technique based on these similarity principles. The behavior of the spray in a swirling flow was investigated. The spray with different breakup length shows different behavior in the same swirling flow.

Experiments and modeling of the fuel spray trajectory and dispersion influenced by both a swirling gas flow and wall impingement were performed under simulated direct injection (D.I.) diesel engine conditions at a high pressure and high temperature. A spray was injected into the steady swirling gas flow and impinged on the simulated piston cavity wall in a constant-volume bomb. High-speed Schlieren photographs provided the informative data on the behavior of the spray vaporizing in such diesel-like circumstances. A simplified computational model was developed to describe the spray trajectory and the fuel vapor dispersion in the D.I. diesel combustion chamber. The model includes the effects of the breakup on the trajectory and the vaporization of the spray, and the effects of the swirling gas flow and the wall impingement on the dispersion of the fuel vapor.

The combustion processes in the prechamber and the main chamber of a small indirect injection (I.D.I.) diesel engine were observed simultaneously by high-speed photography. These observations made it possible to characterize the behavior of flames in both chambers, that is, ignition of fuel, developing and rotating flames in the prechamber, and a flame jet spouting into the main chamber. The effect of engine variables, such as fuel injection timing, cross-sectional area of a throat, fuel injector location, and a recess in a piston top, on the combustion process as well as the engine performance were considered. A flame jet spouting into the main chamber separated into two directions and induced two vortexes. Brown sooty flames appeared along the prechamber wall and inside the flame jet which struck on the piston top. The higher-velocity flame jet and the two Intense vortexes induced by the flame jet realized superior fuel consumption and lower smoke emission.

In-cylinder flow and fuel behaviors in the piston cavity of a direct injection SI engine were measured by using PIV and LIF. The effect of the cavity wall on the mixing process was the focus in this study. The optical prism was installed inside piston to observe air flow and fuel behavior on a horizontal plane of the cavity combustion chamber in the piston. The fuel spray mainly impinged on the cavity bottom surface and rolled up along the cavity wall near the spark plug by it's own momentum. Then it was evaporated and diffused by swirl flow. The effect of fuel injection timing on the mixing process was also investigated. Earlier injection timing made fuel momentum small up to the time of impingement. Therefore, the fuel vapor was considerably diffused by swirl flow in the piston cavity and fuel vapor concentration near the spark plug was low.

Among the alternative fuels, dimethyl ether (DME), one of the oxygenated fuels, attracts attention as an alternative fuel for the Diesel engine since the properties of the DME are fitted to the Diesel engine combustion and the know-how development has been made of the mass production of the DME from a natural gas. In this study, experiments were performed of ignition characteristics of the DME and Diesel fuel sprays injected by a D.I. Diesel injector into a high-pressure, high-temperature vessel. The fuel injection was made by a Bosch type injection system. A schlieren optical system was adopted for visualizing the ignition process as well as the vaporization process of the DME and Diesel fuel sprays. The ignition delay was measured by using a photo-sensor which had a sensitivity in the wavelength range from visible to ultraviolet. Pressure and temperature of the ambient air and the oxygen concentration of the ambient air were changed as experimental parameters.

The fuel injection characteristics of Dimethyl Ether(DME) were calculated and compared with the calculated results of diesel fuel using a simulation model of an in-line diesel injection system in order to clarify the differences between the injection characteristics of the two fuels. Moreover, numerical analyses for the DME injection were performed while changing the fuel parameters and the injection system parameters in order to estimate the effects of these parameters on the fuel injection characteristics. The effects of some of these parameters were evaluated by experimental results conducted in a constant volume vessel. Furthermore, the spray tip penetration was calculated using the computed results of the injection pressure. As a result of this study, the injection characteristics of the DME fuel are basically confirmed. By the macroscopic analyses of these spray characteristics, the DME spray behavior in a combustion chamber can be estimated.

In order to improve thermal efficiency of spark ignition (SI) engines, an improved technology to avoid irregular combustion under high load conditions of high compression ratio SI engines is required. In this study, the authors focused on high pressure gasoline direct injection in a high compression ratio SI engine, which its rapid air-fuel mixture formation, turbulence, and flame speed, are enhanced by high-speed fuel spray jet. Effects of fuel injection pressure, injection and spark ignition timing on combustion characteristics were experimentally and numerically investigated. It was found that the heat release rate was drastically increased by raising the fuel injection pressure. The numerical simulation results show that the high pressure gasoline direct injection enhanced small-scale turbulent intensity and fuel evaporation, simultaneously.

A new optical measuring technique of tip penetration of a diesel fuel spray was developed by detecting the arrival times of the spray tip at several light sheets which were preset at various axial locations downstream. Verified by the instantaneous photographic technique, it was confirmed that this technique is effective, with sufficient accuracy, for measuring the spray tip penetration much more easily than the conventional photographic technique. The tip penetrations of diesel sprays injected through single-hole nozzles with various orifice lengths and diameters has been investigated over a wide range of the operating conditions by this technique. The spray injected through two multihole nozzles, either with or without a sac volume, has also been characterized. The results showed that the spray tip penetration is affected somewhat by the operating conditions. Eventually it is affected by the injected fuel momentum flowrate, nozzle geometry and ambient gas density.